| Marca | KLOP256 |
|---|---|
| Fabricante | KLOP256 |
| Dimensiones del paquete | 32.79 x 9.8 x 1.1 cm; 50 gramos |
| Material | Aluminio |
| Fuente de alimentación | Funciona con cable eléctrico |
| Incluye baterías | No |
| Necesita baterías | No |
| Tipo de bombilla | LED |
| Peso del producto | 50 g |
Envío gratis con tu primera compra
Elige la opción "Envío gratis con tu primera compra" al tramitar el pedido. Ver condiciones
Ofertas relacionadas con este producto
Página 1 de 1 Volver al inicioPágina 1 de 1
Preguntas y respuestas de los clientes
Opiniones de clientes
Principales reseñas de España
Ha surgido un problema al filtrar las opiniones justo en este momento. Vuelva a intentarlo en otro momento.
Revisado en España el 19 de febrero de 2021
Tamaño: Tamaño libreCompra verificada
Revisado en España el 5 de marzo de 2021
Tamaño: Tamaño libreCompra verificada
Revisado en España el 19 de diciembre de 2020
Tamaño: Tamaño libreCompra verificada
Revisado en España el 8 de diciembre de 2020
Tamaño: Tamaño libreCompra verificada
La mejor tira led
Por Alejandro Letxu el 8 de diciembre de 2020
Buena calidad, fácil de montar con los raíles y adhesivos que trae. Se puede conectar en serie a otros componentes con ARGB y heredan los parámetros, en mi caso está conectado a la refrigeración líquida de MSI y bebe el estilo del Dragón Center que está lleva. Compra recomendable 100%
Por Alejandro Letxu el 8 de diciembre de 2020
Imágenes de esta reseña
Reseñas más importantes de otros países
Steve
Good but I needed to make an alteration.
Revisado en Reino Unido el 30 de septiembre de 2020Tamaño: Tamaño libreCompra verificada
Good but I needed to make an alteration.
Revisado en Reino Unido el 30 de septiembre de 2020
So the light strip is actually made by phanteks which was a bonus in my view. From the pictures I expected the light to be tubular in shape but it isn't it's more or a rectangle with a rounded shape on top. This means it can only bend left or right (across the section when viewed with the part that lights up facing you) and not forwards or backwards. As a result I couldn't put it where I intended to in my case as there wouldn't have been enough clearance for the glass to slide on. I therefore decided to put it along the motherboard but since the light is 50cm long obviuously that was way more than necessary (see pic). In the end I decided it was worth the risk to CUT the bar to the required length as I wouldn't have used it otherwise regardless. Used a small piece of electrical tape to insulate the end which was cut and then used the rubber end grommit to seal. Long story short if you need to cut this to size you can - just make sure to cut the right end as there is a different connector on each end and make sure you insulate it properly.
Revisado en Reino Unido el 30 de septiembre de 2020
Imágenes de esta reseña
Karl Williams
Fantastic diffused RGB lighting strip
Revisado en Reino Unido el 10 de marzo de 2021Tamaño: Tamaño libreCompra verificada
Fantastic diffused RGB lighting strip
Revisado en Reino Unido el 10 de marzo de 2021
I was a little apprehensive of buying an LED strip kit just due to the number of products available to buy. I chose this one over others due to it's built in diffusion of the light and I'm glad I did.Revisado en Reino Unido el 10 de marzo de 2021
The kit arrived complete with plastic running attachments which not only stick to the back of the case with the supplied 3M sticky pads, but they also have holes pre-drilled to be able to screw in behind the motherboard to the case fixing points.
Once the clips were ran where I wanted, running the strip was straight forward. There is enough flexibility in the strip to navigate through and around existing wiring within the case without having to remove or detach anything. The 600mm wiring extension is more than ample to allow cable management without stressing the wires.
The strip itself covers two full sides of my microATX motherboard and has a short left over length tucked in at the bottom which, when looking at it, is where the GPU covers anyway so you cannot tell it only goes so far across.
There are expansion ports on both ends of the wiring adapter to allow more strips to be added.
The strip runs on a 5v 3 pin plug, which needs connecting to some form of USB controller. It is not a 12v 4 pin plug which is what is required to run from my motherboard. I already had a pre-existing LED Controller so I was able to just plug and play.
The LED strip works really well with ASUS Aura Sync and runs well with the case and GPU fan I already have which are both synced through the same software.
Overall very impressed and I will buy another strip once I've decided where I want to put it. After all, you can never have too much RGB!
Imágenes de esta reseña
chris
A flexible and aesthetically pleasing strip for adding some colour.
Revisado en Reino Unido el 15 de agosto de 2020Tamaño: Tamaño libreCompra verificada
A flexible and aesthetically pleasing strip for adding some colour.
Revisado en Reino Unido el 15 de agosto de 2020
Now this is a lovely lighting strip, it's actually a Phanteks strip but that's not mentioned in the listing. All the LED's are addressable if your motherboard or lighting controller supports that (MSI mystic light definitely does). The lights are nicely defused through the cover, which adds a much calmer ambient colour to the build. Only gripe is that the included 3M double sided pads are useless, they can't hold on at all. I've switched to a different 3m tape but even that struggles. Vertically maybe it's not so bad but be aware if you're mounting to the top like I did. Would definitely recommend this strip though, it really is very flexible!
Revisado en Reino Unido el 15 de agosto de 2020
Imágenes de esta reseña
Steven
Usual poor quality Phanteks
Revisado en Reino Unido el 8 de marzo de 2021Tamaño: Tamaño libreCompra verificada
T. Gounden
Easy to use
Revisado en Reino Unido el 29 de octubre de 2020Tamaño: Tamaño libreCompra verificada